基于DTW距离的拖拉机传动轴载荷样本长度计算方法

针对工程领域载荷样本长度确定方法对农业机械载荷适用性较差的问题,提出了一种基于动态时间扭曲(DTW,Dynamic Time Warping)距离计算载荷样本长度的方法。首先,运用无线扭矩传感器获取犁耕作业下拖拉机传动轴的动态载荷,结合传动轴犁耕作业下的载荷特点,划分作业工况;再将作业循环叠加并经过归一化处理后进行DTW距离计算,确定传动轴载荷样本长度;最后,计算参数外推中均值混合正态分布函数的拟合参数相对误差。结果表明,运用DTW距离方法确定的载荷样本长度,能够使均值双正态分布函数拟合得到的参数相对误差保证在10%以内。近似均值精度估计法和均值曲线拟合法的拟合参数相对误差最大值分别为126.06%和80.62%,而基于DTW距离计算方法的拟合参数相对误差最大值为5.43%,验证了基于DTW距离的载荷样本长度计算方法的适用性。研究结果可为拖拉机传动轴田间试验载荷样本长度确定提供参考。     

新疆日光温室前屋面的风载数值模拟分析

【目的】 对日光温室前屋面风载大小和变化趋势进行模拟,可辅助前屋面骨架结构优化设计和前屋面实际风载计算,为提前预测和防灾功能提供科学依据。【方法】 将日光温室墙体、保温被和骨架等结构简化,使用UG 软件对日光温室进行造型,将模型与空气进行布尔求差,得到整体模型,将整体模型导入到ANSYS ICEM中,进行网格划分,得到保温被4种工作状态薄膜风压。再通过Y向的9条曲线画出不同条件下风压变化对比曲线。【结果】 在无保温被和保温被全铺时,薄膜最南侧风压最高,约1.014×10⁵Pa,往北侧风压逐渐降低,脊高位置风压最小约1.010×10⁵Pa。由于最南侧风遇到薄膜阻碍,造成风压的升高,而北侧接近日光温室顶端,风速快,而风速快的位置风压小。在保温被全卷及半卷时,也是最南侧风压较最高,约1.014×10⁵Pa,往北有风压的降低,总体屋面风压变化比较小,约1.013×10⁵Pa。只是保温被半卷时,在保温被卷放位置会有风压的突变为1.012×10⁵Pa。【结论】 无保温被、保温被全铺、保温被全卷及保温被半卷4种情况南侧风压较大且相差不大,但越往北侧,保温被全卷或半卷会造成薄膜风压的升高,尤其是顶部的突然升高。保温被全铺是最佳防风方案。南侧风压高,南侧前屋面钢骨架拱形段的性能对日光温室结构稳定性和安全性至关重要,设计和建设时需要着重计算和核验。     

城镇污水处理厂供配电系统分析

污水处理已成为城市建设中必不可少的环节,所以对相应的配套工程也提出了更高的要求,本文将对污水处理厂的供配电系统进行简要的分析。     

定量泵负载敏感系统卸荷压力冲击抑制研究

定量泵负载敏感系统在快速卸荷时容易出现压力冲击现象,对系统的可靠性和寿命产生较大危害。三通压力补偿阀是定量泵负载敏感系统中关键的调压元件,本文以三通压力补偿阀为切入点,建立定量泵负载敏感系统功率键合图模型,基于键合图模型推导系统的状态方程,建立Matlab动态仿真模型,探讨系统卸荷压力冲击的抑制方案。基于系统仿真模型,首先对系统卸荷压力冲击的仿真与试验进行对比,验证了仿真模型的正确性;然后,针对三通压力补偿阀的系统压力腔阻尼、阀芯直径、Ls腔阻尼、阀口锥角等关键参数,对卸荷压力冲击影响规律进行仿真;最后,基于关键参数对卸荷压力冲击影响规律的分析,提出了一种"小阀芯、双阀口"型三通压力补偿阀结构优化方案,并对其卸压冲击抑制效果进行了仿真和试验。结果表明,该方案可以有效抑制卸荷压力冲击,优化后系统卸压冲击压差比原系统降低了89%,卸荷压力降低了20%,进一步实现了节能。     

Does sand content in spawning substrate result in early larval emergence? Evidence from a lithophilic cyprinid fish

The spawning success of lithophilic salmonids is strongly influenced by the fine sediment content (“fines”) of spawning substrates, yet knowledge on the impacts of fines on the spawning of non‐salmonid lithophiles remains limited, despite their ecological and socio‐economic importance in European rivers. Consequently, the aim here was to use an ex‐situ experiment to investigate the impact of sand content on egg survival and timing of larval emergence of the surface‐spawning cyprinid European barbel Barbus barbus. Thirty incubator boxes within a recirculating system were filled with one of five experimental sediment mixtures (0%–40% sand by mass) that each contained 300 fertilised eggs at a depth of 50 mm. Emerged, free‐swimming larvae were captured and counted daily to assess grain‐size effects on larval survival and emergence. Specifically, total proportion of emerged larvae, cumulative daily proportion of emerged larvae and time required to reach 50% emergence were measured during the study. Whilst the proportion of sand in the sediments did not have a significant impact on egg‐to‐emergence survival (mean survival per treatment 75%–79%), it significantly affected the timing of larval emergence to the water column; early emergence was detected in treatments with elevated sand content (on average, 50% emergence after 12–13 days versus 19 days in the control). Similar to findings from salmonid studies, these results suggest high sand content in spawning gravels can influence timing of larval emergence and potentially cyprinid lithophilic fish survival.     

基于耦合协调度的大理河流域径流和输沙关系分析

深入研究流域水沙关系变化是解决黄河流域高质量发展关键问题的重要科学途径之一。自20世纪50年代以来,黄河中游地区实施了大规模的水土保持工程,径流和输沙显著减少,水沙关系发生变化。该研究利用Mann-Kendall趋势检验法分析了1960—2015年来大理河流域的径流输沙变化趋势,并构建基于耦合协调度理论和Pettitt检验方法的径流输沙关系变异诊断方法,识别大理河流域径流和输沙关系的突变点,并通过Copula方法进行验证。结果表明:1)大理河流域径流输沙在月尺度和年尺度呈现显著的下降趋势;2)大理河流域径流和输沙关系在1996年发生显著突变;3)径流输沙关系发生突变后,径流和输沙均明显减少,输沙的减少幅度比径流的减少幅度高29.19个百分点,径流对输沙贡献程度下降幅度为5.10%,单位径流的输沙能力降低;4)淤地坝建设和植被恢复是造成大理河流域水沙变化的主要因素,修建淤地坝和恢复植被对减少泥沙具有积极作用。研究成果可以为进一步深化理解大理河流域水沙关系变化以及水土流失治理提供依据。     

Adjusted method of penis fixation during boar semi-automatic semen collection aiming to reduce bacterial contamination

Semen collection has an essential role in the initial bacterial load in boar ejaculates and extended semen. The study aimed to explore the efficacy of an adjusted penis fixation in a semi-automatic collection system on reducing bacterial contamination of ejaculates in two-boar studs with different scenarios. Historically, stud A had low levels of bacterial load in raw semen, while stud B had a high level of contamination. A total of 56 mature boars had their semen collected using two methods of penis fixation: (a) Traditional: The penis was fixed directly with the artificial cervix and transferred to the adjustable clamp; (b) Adjusted: The fixation was performed with one gloved-hand, and after exteriorization, the penis was gripped using the artificial cervix with the other gloved-hand and transferred to the adjustable clamp. The bacterial load (p = .0045) and the occurrence of ejaculates >231 CFU/ml (p = .0101) were reduced in the Adjusted compared to the Traditional method. Bacterial load was reduced when using the Adjusted method in stud B (p = .0011), which showed a greater occurrence of critical factors for bacterial contamination (p ≤ .0034). The Adjusted method reduced the occurrence of ejaculates >231 CFU/ml when the preputial ostium was dirty (p = .016) and the duration of semen collection was >7 min (p = .022) compared to the Traditional method. In conclusion, the Adjusted penis fixation was efficient in reducing bacterial load of ejaculates, mainly in boar stud B, which had high contamination challenges.     

山东省菏泽市某规模猪场不同猪群伪狂犬病野毒感染情况调查

为了解规模猪场不同猪群的伪狂犬病病毒(PRV)感染情况及场区病毒载量分布特点,在山东省菏泽市某规模猪场,利用实时荧光定量PCR方法,对该猪场不同孕龄母猪、不同阶段生长猪群,以及各生产阶段场区环境,采集猪鼻拭子和场区环境拭子进行PRV-gE核酸检测,并对检测结果进行统计分析。结果显示:在294份猪鼻拭子中,检出42份PRV-gE核酸阳性,总阳性率为14.28%;母猪群PRV-gE阳性率为17.83%(23/129),且妊娠前后各阶段阳性率呈先上升后下降趋势,中期较高(24.00%),但差异不明显(P>0.05);不同阶段生长猪群的平均PRV-gE阳性率为11.52%(19/165),随日龄增加,阳性率也呈先上升后下降趋势,80~90日龄育肥猪最高(28.13%),与其他生长阶段猪群差异明显(P<0.05);除饲料、水源、上猪台和出猪台外,其他大部分场区环境均检测到PRV-gE核酸阳性;育肥猪群病毒载量最高,为3.6×105拷贝数/mL,其猪舍环境的病毒载量也较高,与其他环境及生长阶段猪群差异均明显(P<0.05)。结果表明,不同猪群包括免疫猪群均可遭受PRV野毒感染,尤其是母猪妊娠中期和猪育肥阶段早期,且大部分场区环境均可被污染。结果提示,规模猪场要加强各种猪群尤其是育肥猪群的伪狂犬病免疫,通过监测来调整和优化免疫程序,同时要加强生物安全,防止病毒传入和扩散。     

Estimation of Runoff,Peak Discharge and Sediment Load at the Event Scale in a Medium‐Size Mediterranean Watershed Using the Annagnps Model

In this paper, the Annualized Agricultural Non‐Point Source (AnnAGNPS) model has been used to estimate runoff, peak discharge and sediment load at the event scale in a Mediterranean watershed. The study area is the Carapelle torrent, Southern Italy (area = 506 km²), where continuous rainfall, streamflow and sediment load data are available. Nineteen flood events have been registered in the period 2007–2009 and were used for the application of the model. The aim of the paper is to evaluate the predictive accuracy of the model at the event scale, in a medium‐size watershed, given the specific conditions of the semi‐arid environments. A sensitivity analysis has been carried out to assign the correct parameterization: the mean normalized output variation of the most meaningful input parameters pointed out the influence of the curve number on runoff, peak discharge and sediment load predictions (values greater than 1); the MN Manning's roughness coefficient and K, C and P factors of the universal soil loss equation showed a moderate influence on sediment load simulations (values between 0·5 and 1). The selection of the Soil Conservation Service synthetic storm types has been based on the observed storm events analysis to improve the peak discharge simulations. The model prediction has proved to be good for runoff (R² = 0·74, NSE = 0·75, W = 0·92) and peak discharge (R² = 0·85, NSE = 0·70, W = 0·94), and satisfactory for sediment yield (R² = 0·70, NSE = 0·63, W = 0·91). The relative error is lower for high events; this result is quite interesting in semi‐arid environments, where most of the annual sediment yield is concentrated in a few, severe events. Copyright © 2013 John Wiley & Sons, Ltd.     

卷盘式喷灌机卷盘驱动负载计算与分析

为优化卷盘式喷灌机驱动结构,研制高效卷盘喷灌机驱动器,需要对卷盘式喷灌机的卷盘负载情况进行计算和分析。为此,以软管牵引式卷盘喷灌机为对象,建立了卷盘负载转矩计算的物理模型,理论推导了在运行时的卷盘负载转矩数学计算模型。以JP50和JP75型卷盘式喷灌机为例,按推导所得数学模型进行计算,得到了运行时卷盘负载转矩随已回卷PE管长度的变化规律和估计值。计算结果表明:JP50型卷盘式喷灌机运行时最大负载转矩约为960N·m,JP75型为6 001N·m;卷盘负载转矩随已回卷长度的增加而减小,且当卷盘回卷半径变化时,负载转矩将突然变大;负载转矩的大小和变化规律只与喷灌机的参数和运行条件有关,与运行时的速度无关。